- 0Cart
-
Your shopping cart is empty.
-
more items in the cart...
Cart Total: $0.00
Proceed to Checkout
Your shopping cart is empty.
Cart Total: $0.00
Proceed to Checkout
Item specifics
Product Description
THINKCAR THINKTOOL Pros+10inch Online Programming Car full system Diagnostic Tool with 34+ Special service, ADAS Calibration, Active test, TPMS Function, Android 10 OS running on 10-inch HD IPS Touch Screen + 128GB Memory + 2 years free update online You Deserve to Have a THINKCAR THINKTOOL PROS+ 1. High-end online programming capabilities. THINKCAR THINKTool PROS+ Language English, German, Spanish, French, Italian, Japanese, Portuguese, Russian, Polish, Turkish, Dutch, Hungarian, Chinese Traditional, Korean, Greek, Arabic, Denish, Persian, Romanian, Croatian, Finnish, Swedish, Czech The Advance Function of THINKCAR ThinkTool Pros+ - ONLINE PROGRAMMING ( Does not works in American & Spain ): Think Tool Pros+ supports programming and coding, which is to write the relevant control information of the software into the automotive computer's programmable EPROM or FLASH by making use of the electronic communication transmission technology. Due to policy restrictions, the programming function is not open in the following countries, Some North American countries and regions, United States, Portugal, Spain, Canada, Which system needs online programming? 1. Engine Control Programming THINKCAR THINKTool PROS+ supports Full System Diagnostic: Engines/Auto Transmission/Airbags/Immobilizer/Key Coding/ABS/Cruise Control/Instruments/ Self Leveling Suspension systems/Seats/Doors/Gateway/Steering Angle/Air Suspension/Body Systems/Electronic Power Steering & Motor Assisted/Power Steering/Tyre Pressure/Rain Sensors/4WD System/Stabilizer/Intelligent Parking Assist/Door Motors/Audio Systems/Air Conditioning/Tiptronic/Anti Theft/Soft Top/Headlamp Leveling/Central Locking/Automatic Clutch/ DPF Reset/Electric Windows/Plip Programming/Heated Rear Window/Xenon Headlights/Wash Wipe/Fuel Burning Heater/Transfer Box/Seat Memory/Oil Life Service Reset/Sliding Doors/Electronic Throttle/Navigation System/Rollover Sensor/Cruise Control/ Multi Function Steering Wheel/Aux Heating/Electronic Parking Brake/Clutch Electronics etc. (Great for car repair shops and mechanics to improve business) THINKCAR THINKTOOL PROS+ Supports ECU CODING and Full Bi-Directional Control ( ACTIVE TEST) Function : ECU CODING Function : Because every automobile actuator has a record code in ECU, which is the basis for automobile computer to mobilize their work. ThinkCar ThinkTool PROS+ is equipped with advanced ECU coding function for addressing the following issues: Full Bi-Directional Control ( ACTIVE TEST) Function: This diagnostic tool ThinkCar ThinkTool PROS+ supports active test (Bi-directional control) to request information or command a module to perform specific tests and functions. For instance, in the case of OBD II generic information Mode 1, you can initiate a request for information from the powertrain control module, and the PCM responds by sending the information back to the scan tool for display. This ThinkCar ThinkTool PROS+also have the ability to actuate relays, injectors, coils, or perform system tests, etc. THINKCAR THINKTOOL PROS+ Support TPMS Diagnostic function ( works with ThinkTPMS G1, It need buy seperate ) THINKTOOL Pros+ can work with wireless tire pressure diagnostic tool (optional accessory) toachieve the features of TPMS activation, programming and learning. ThinkTool PROS+ Supports Key Programming : >>>>Add, Delete & Reprogram Keys THINKCAR THINKTOOL PROS+ Supports ADAS calibration (works with ADAS tool) Advanced Driver Assistance System (ADAS) is an electronic component in a vehicle, including various safety functions of the vehicle, such as automatic emergency braking (AEB), lane departure warning (LDW),lane keeping assist, blind spot elimination, night vision camera and Adaptive lighting. ThinkTool PROS Supports Guided Function for Volkswagen/Audi, the following function need Guided Function: √Service Regeneration,Particle Filter(DPF) 28 Maintenance function : THINKTOOL Pros+/Pros supports matching, coding, programming of most vehicles' programable modules,and most commonly used maintenance and reset functions, namely, Oil Reset, Elec. Throttle Adaption, IMMO Service, Injector Coding, Break-pad Reset, Steering Angle Reset, ABS Bleeding, AFS Reset, Battery Matching, A/T Learning, DPF Regeneration, EGR Adaption, TPMS Reset, Sunroof lnitialization, Suspension Matching, Gear Learning, Airbag Reset, ODO Reset, AdBlue Reset, A/F Reset,CoolantBleeding, Language Change, NOx Sensor Reset, Seat Calibration, Stop/Start Reset, Transport Mode,Tyre Reset, Windows Calibration. ThinkCar THINKTOOL PROS+ supports 8 Modular expansion Thinkprinter , Think work lingt , Think Videoscope , Think TPMS G1, Think battery tester, Think scope box, Think thermal imager, Think moudledock 12 Data Graphs shows in the Same Screen it is better you can compare and Analysis the Data, easy to find the problem of the car ! ThinkCar ThinkTool PROS+ can support 24V trucks (it need with with HD model. ) ThinkCar ThinkTool PROS+ is designed with Holder, you can stand it on the desk, free your hands, more convinet to operate !!! THINKCAR THINKTOOL PROS+ has 28 service functions which allows you to reset various systems in your vehicle. support more function than other scanners priced similarly : 1. Oil Reset The lightening of the car maintenance light indicates that the vehicle needs maintenance. Reset the mileage or driving time to zero after the maintenance, so the maintenance light will go out and the systemwill start a new maintenance cycle. 2. Elec.Throttle Adaption Elec. Throttle Adaption is to utilize the car decoder to initialize the throttle actuator so that the learningvalue of the ECU returns to the initial state. By doing these, the movement of the throttle (or idle motor) can be more accurately controlled, thus adjust the intake volume. 3. Steering Angle Reset To reset the steering angle, first find the relative zero point position for the car to drive in straight line. Taking this position as reference, the ECU can calculate the accurate angle for left and right steering. After replacing the steering angle position sensor, replacing steering mechanical parts (such as steering gear box, steering column, end tie rod, steering knuckle), performing four-wheel alignment, or recovering car body, you must reset the steering angle. 4. Battery Matching This function enables you to perform a resetting operation on the monitoring unit of vehicle battery, in which the original low battery fault information will be cleared and battery matching will be done. 5. ABS Bleeding When the ABS contains air, the ABS bleeding function must be performed to bleed the brake system to restore ABS brake sensitivity. lf the ABS computer, ABS pump, brake master cylinder, brake cylinder, brakeline, or brake fluid is replaced, the ABS bleeding function must be performed to bleed the ABS. 6. Break-pad Reset lf the brake pad wears the brake pad sense line, the brake pad sense line sends a signal sense line to theon-board computer to replace the brake pad. After replacing the brake pad, you must reset the brake pad. Otherwise, the car alarms. 7. DPF Regeneration DPF regeneration is used to clear PM (Particulate Matter) from the DPF filter through continuous combustion oxidation mode (such as high temperature heating combustion, fuel additive or catalyst reduce PM ignition combustion) to stabilize the filter performance. 8. Gear Learning The crankshaft position sensor learns crankshaft gear machining tolerance and saves to the computerto more accurately diagnose engine misfires. lf gear learning is not performed for a car equipped with Delphi engine, the MlL turns on after the engine is started. The diagnostic device detects the DTC P1336 'gear not learned'. In this case, you must use the diagnostic device to perform gear learning for the car. After gear learning is successful, the MIL turns off. After the engine ECU, crankshaft position sensor, orcrankshaft flywheel is replaced, or the DTC 'gear not learned" is present, gear learning must be performed. 9. IMMO Service To prevent the car being used by unauthorized keys, the anti-theft key matching function must beperformed so that the immobilizer control system on the car identifies and authorizes remote control keys to normally use the car. When the ignition switch key, ignition switch, combined instrument panel, ECu, BCM, or remote control battery is replaced, anti-theft key matching must be performed. 10. Injector Coding Write injector actual code or rewrite code in the ECU to the injector code of the corresponding cylinder soas to more accurately control or correct cylinder injection quantity. After the ECU or injector is replaced, injector code of each cylinder must be confirmed or re-coded so that the cylinder can better identifyinjectors to accurately control fuel injection. 11. TPMS Reset After the tire pressure MIL turns on and maintenance is performed, the tire pressure resetting function must be performed to reset tire pressure and turn off the tire pressure MIL. Tire pressure resetting must be performed after maintenance is performed in the following cases: tire pressure is too low, tire leaks, tire pressure monitoring device is replaced or installed, tire is replaced, tire pressure sensor is damaged, and tire is replaced for the car with tire pressure monitoring function. 12. Suspension Matching This function can adjust the height of the body. When replacing the body height sensor in the airsuspension system, or control module or when the vehicle level is incorrect, you need to perform this function to adjust the body height sensor for level calibration. 13. AFS Reset This feature is used to initialize the adaptive headlamp system. According to the ambient light intensity, the adaptive headlamp system may decide whether to automatically turn on the headlamps, and timely adjustthe headlamp lighting angle while monitoring the vehicle speed and body posture. 14. A/T Learning This function can complete the gearbox self-learning to improve gear shifting quality. When the gearbox is disassembled or repaired (after some of the car battery is powered off), it will lead to shift delay or impact problem. In this case, this function needs to be done so that the gearbox can automatically compensate according to the driving conditions so as to achieve more comfortable and better shift quality. 15. Sunroof Initialization This function can set the sunroof lock off, closed when it rains, sliding / tilting sunroof memory function, temperature threshold outside the car etc. 16. EGR Adaption This function is used to learn the EGR (Exhaust Gas Recirculation) valve after it is cleaned or replaced. 17. ODO Reset a) ODo reset is to copy,write, or rewrite the value of kilometers in the chip of odometer by using a car diagnostic computer and data cable, so that the odometer shows the actual mileage. 18. Airbag Reset This function resets the airbag data to clear the airbag collision fault indicator. When the vehicle collidesand the airbag deploys, the corresponding fault code of the collision data appears, the airbag indicator lights up, and the fault code cannot be cleared. Since the data inside the airbag computer is disposable, it is required that all new accessories must be replaced, but after performing this function, the data of theairbag computer can be recovered and the fault code can be cleared, the airbag light will go out, and theairbag computer can continue to use. The Other Function of THINKCAR THINKTool PROS+ : Auto VIN read Function: THINKCAR ThinkTool Pros+ Supports Car List : Supports more than 93 brands Vehicles. ThinkCar ThinkTool PROS+ Supports 2 Years free Update + 5 Years Warranty + Lifetime free Technicial support ( can Remote Technical via TeamViewer) ThinkTOOL PRO+ is with 2 years free Update How To Register THINKCAR ThinkTool Pros+ : Step 1: Setting language & Time Zone, Connect WIFI How To Printer the Diagnostic Report : Connect ThinkPrinter to print , easy to operate ! High-end hardware configuration of THINKCAR ThinkTool Pros+ : Operating System: Android 10 The Packing of THINKCAR ThinkTool Pros+ : 1pc ThinkTool pros+ 10.1 inch Tablet PC |