|
Item specifics
Product Description
X300 DP Plus Register & Upgrade Guide OBDSTAR X300 Key Master DP Plus Hardware Advantages:1. Built-in VCI box2. 8-inch touchscreen3. Charge directly via OBD interface4. Practical and high-end gift box5. Industrial design with silicone case6. Back bracket design:prop on the steering wheel or stand on the table7. With 4 Toyota simulation keys (the fifth is coming soon)8. P001 programmer: EEPROM adapter + RFID adapter + Key Renew adapter9. Add the clip of reading SOP 8PIN EEPROM10. C001/C002 circuit board to read and write chip data with welding11. IMMO induction coil to detect the key induction coil failure of the vehicle.12. Add wiring harness of ECU reading by OBD (for ECU cloning and switch activation)OBDSTAR X300 Key Master DP Plus Software Advantages: IMMO:1. EEPROM2. Renew Key3. Key programming4. Remote programming Cluster Calibrate: wild vehicle coverage, pls check the carlist Diagnosis: realize all vehicle systems diagnosisSpecial FunctionsTPS/ABS/EPB/DPF/TPMS/SRS Reset/Fuel Injector/Gear Learning/Battery Matching/ECU Programming/Throttle Matching/Oil/service reset/Steering Angle Reset/Remote Manual Setting/Electronic Steering Reset/CVT Learning/value ResetECU Clone1. ECU Clone, means ECU duplication.The device copies all the data from the original vehicle ECU, and then writes all data copied into ECU with the same hardware to realize the same ECU function with the original vehicle.2. Clone directly when replacing a new or a used ECU!Without online matching in 4S store or removal of ECU bonding wire for reading and writing! Directly write without dismantling OBD!3. Three features for ECU Clone:A. Free of 4S online:break monopoly from 4S, benefiting automobile maintenance industryB. Simplified operation procedures: realize foolproof operationC. Non-dismantling with zero risks: read and write data without dismantling ECUSwitch Activation Function(Today many instruments or audio of vehicles activate secondary power supply to go into power-on status by relevant module CAN communication on the vehicle, but sometimes an instrument or an audio is separated from vehicle CANBUS network, causing startup failure when it needs to be repaired by an auto technician. This function can simulate CAN communication to activate secondary power supply, so the instrument or the audio enters into power-on status. In this way, it not only can test and verify the instrument or the audio, but also save an enormous cost for an auto technician to purchase a large number of startup platforms of various vehicles and wiring harnesses!)Add “Help” Functions1. including built-in testable vehicle models, upgrade announcement, features, help notes and wiring diagrams, etc.2. Carlist and upgrade announcement, all details are available on the device3. Customers can look up the features or uniquely support functions on the device4. Help notes: built-in help notes for each model or function5. Wiring diagrams: built-in ECU wiring diagrams, more intuitionistic and convenientTECHNICAL PARAMETER● Operation system: Android 5.1.1● CPU: Exynos4418 Dual Core ARM Cortex A9 1.4GHz● Battery: 3700mA, rechargeable polymer lithium battery● Extension memory card: 32G Micro SD (TF) card supported● Memory capacity:1GB● Storage capacity: 32GB● LCD: 8.0 inch● LCD resolution: 1280*800● Touch screen: Capacitive touch screen● Camera: 5 mega rear view camera● Wi-Fi: supported● Working temperature: -10℃ ~ 55℃（14℉ ~ 131℉ ）● Storage temperature: -20℃ ~ 70℃（-4℉ ~ 158℉ ）● Weight: about 1.0 Kg● Dimension: 254mm*174*mm*35mmCONFIGURATIONS A Package: Immobilizer+Special function(EEPROM+Key Renewing)Adapter(P001 programmer+C001circuit board+C002 circuit board+W001 cable+W002 data cable+W003 data cable+Toyota smart key Emulator)+others(Ignition coil+Remote tester) B Package: Immobilizer+Special function(EEPROM+Key Renewing)+ cluster calibration+Adapter(P001 programmer+C001 circuit board+C002 circuit board+W001 data cable+W002 data cable+W003 data cable+Toyota smarkt key Emulator)+others(Ignition coil+Remote tester) C Package: Immobilizer+cluster calibration+Diagnosis+Special function (Oil rest +ABS+Battery matching+ECU programming+EPB+Throttle programming+Airbag rest+TPMS+Steering angle rest+OBDII+DPF+Injector code+Supension matching+Gear learning+CVT learning+EEPROM+Key renewing+ECU cloning)Adapter(P001 programmer+C001 circuit board+C002 circuit board+W001 data cable+W002 data cable+W003 data cable+Toyota smarkt key Emulator)+others(Ignition coil+Remote tester) 1. Clone ECU Clone ECU means copy ECU, that is the OBDSTAR X300 DP Plus copies the data from the original car ECU, then write it into another same ECU hardware, so that it can achieve the same function as the original ECU. When you want to change the new ECU or the second ECU, if you use X300 DP Plus to clone via OBD, you won't need to go to the 4s store to do the online programming or dismantle ECU to weld, read & write. ECU clone Pros : No need to go to 4S shop, convenient, fast and save money. Simplify the operating steps, even the amateur can also operate. No need to dismantle and weld the ECU to read & write, it is zero risk to clone ECU via OBD with the X300 DP Plus. 2. Switch activation function Nowadays, many car models' secondary power supply of the dashboard or audio equipment needs to be activated to enter the boot status through the related module CAN. However, when the car technician maintains the dashboard / audio equipment, the main unit is out of the CANBUS network so it maybe won't boot. X300 DP plus " switch activation function" can emulate the CANBUS communication to active the power supply of dashboard / Audio so that it can enter the boot status, then it will test and verify the dashboard and the Audio, also the technician can save money avoiding to purchase many the boot platform and cables of kinds of car models. 3. Adds the "Help" function including the testable car models, update notice, special features, help instruction, wiring diagram etc.
OBDSTAR X300 DP Plus Hardware Features: 1. The built-in VCI box offers more stable communication. 2. The 8" touch screen offers better vision experience. 3. Allow the user tocharge by the OBD port of car. Not like the X300 DP 7" Pad, which need to be 100% charged before use. 4. With specialized toolkit, high grade and practical. 5. Industrial -grade design, comes with the silicone sleeve 6. The back bracket allows the user to hang it on the steering wheel or stand on the table, which brings great convenience to the operator. 7. Comes with forToyota Lexus Emulators(The first 4 pieces are already released, and the 5th one is under development) 8. The following 3 adapters are integrated into the X300 PAD plus: EEPROM /PIC 2-in-1 adapter, RFID adapter (VW Audi 4th / 5th IMMO programming and other cars e.g Porsche, BMW, Fiat etc.) and Renew Key PCF79XX adapter. 9. Adds the clip for readingSOP 8PIN EEPROM. 10. Adds the cables forreading ECU via OBD(Used to clone ECU and active the switch). Different among OBDSTAR X300 DP Plus C Package (Full Version), A Package and B Package:
OBDSTAR X300DP X300 DP Plus C Full Package
OBDSTAR X300 DP Plus X300 PAD2 A Package: Immobilizer+Special function(EEPROM+Key Renewing)Adapter(P001 programmer+C001circuit board+C002 circuit board+W001 cable+W002 data cable+W003 data cable+Toyota smart key Emulator)+others(Ignition coil+Remote tester)
Why OBDSTAR X300 DP Plus is a good investment even expensive
OBDSTAR X300 DP Plus Technical Parameter: OBDSTAR X300 DP Plus X300 Package List: |
eBike Accessories
Motorcycle Parts