LAUNCH Creader 3001 OBD2 Scanner Engine Fault Code Reader Mode 6 CAN Diagnostic Scan Tool for All OBDII Protocol Cars Since 1996 Lifetime Free Update

LAUNCH CR3001 Supports Langauges :

English, French, German, Spanish, Russian, Italian, Polish

LAUNCH Creader 3001 OBD2 scanner is a very Cost-efficient full OBD2 function scanner on the market (the same functions need 40 ). Unlike other car code readers, Launch Creader 3001 is an all in one car code scanning tool. An upgraded version from the more basic code reader with additional functions. It is designed for car owners, DIYers as well as mechanics to determine the cause and solve the problem.

Why Choose LAUNCH Creader 3001?

1. LAUNCH Creader 3001 obd2 scanner Supports O2 Sensor test , EVAP system test, On-Board monitor test, While AD310 and AL319 DOES NOT !

2. LAUNCH CR3001 Add more car models , including cars, SUVs,minivans,light-duty trucks all over the world. But the year supported may vary on different car makes and models.

LAUNCH CR3001 Support Full OBD2 functions, Engine Check including :

Reading Codes:Show the detailed description of the Diagnostic Trouble Code (DTCs)

Erasing Codes & Reset:Turns off Check Engine Light (MIL), clears codes and resets monitors.

Data Stream:Reads and displays live ECU/PCM data stream, plotting functions graphically and stores freeze frame data.

I/M Readiness Status:Shows whether the various emissions-related systems on the vehicle are operating properly and are ready for inspection and maintenance testing.

Read Live Data Stream:Show the information of continuous data stream from a vehicle in live graphic (waveform) display.

View Freeze Frame Data:Check the certain vehicle conditions which are recorded by the on-board computer at the time the emission-related fault occurs.

O2 Sensor Test:Allows retrieval and viewing of O2 sensor monitor test results for the most recently performed tests from the vehicle’s on-board computer.

On-Board Monitor Test:Retrieves and displays test results for emission-related powertrain components and systems.

Read Vehicle Information:Display the information such as VIN (Vehicle Identification Number), CID (Calibration ID) and CVN (Calibration verification number), etc.

Component Test:Certain vehicle components can be actuated by commands sent from the scanner to test their operability

Turn Off ''Check Engine'' Light

Parts might cause your check engine light on include:
1. Gas Cap 2. Oxygen Sensor 3. Air Fuel Ratio Sensor 4. Mass Air Flow Sensor 5. Ignition Coils 6. Spark Plug Wires 7. Spark Plugs 8. Thermostat 9. EGR Valve 10. Evaporatative Emission Canister Purge Valve(EVAP) 11. Catalytic Converter.
If the engine light is not turned off in time
it will Cause Serious environmental pollution , Increased fuel consumption,Increased engine noise.Increased in temperature , ect

How to verify whether the vehicle will pass the emission test with this code reader?

After entering the I/M Readiness, there will be 10 results on the list. Misfire monitor, fuel system, componentmonitor, catalyst monitor, heated catalyst, EVAP system, secondary air sys, 02 sensor, O2 sensor heater EGRand/or WVT. There will be an OK if each of them works fine. [Not all vehicles have these 10 parts]

LAUNCH CR3001 Screen Display

Support Car Models for OBDII diagnostic function:

(Note: CR3001only Support 12V Gasoline& Diesel, Does not support 24V Truck)

American Car :
Need Standard OBD2 Protocols from 2000 to now
for Chrysler , for Ford, for GM, For Jeep ...

European Car :
Need Standard OBD2 Protocols from 2003 to now
For Alfa romeo , for SAAB ,for Acura , for Opel , for Audi for Seat , for Peugeot , for Renault
For Bentley , for Skoda , for Daewoo , for Benz , for Daihatsu , for Land Rover , for BMW , for Vauxhall , for Citroen , for Volvo , for Fiat , for VW , for Ford , for Jaguar...

Japanese/Korean Car:
Need Standard OBD2 Protocols from 2006 to now
for KIA, for Isuzu, for Honda , for Mitsubishi, for Hyundai , for Dacia , for Lexus , for Mazda, for Nissan, for Subaru , for Suzuki, for Toyota..

Chinese Car:
Need Standard OBD2 Protocols from 2009 to now

LAUNCH CR3001 Support OBD 2 protocols car :

1.SAE J1850 PWM(41.6Kbaud)
2.SAE J1850 VPW(10.4Kbaud)
3.ISO9141-2(5 baud init,10.4Kbaud)
4.ISO14230-4 KWP(5 baud init,10.4 Kbaud)
5.ISO14230-4 KWP(fast init,10.4 Kbaud)
6.ISO15765-4 CAN(11bit ID,500 Kbaud)
7.ISO15765-4 CAN(29bit ID,500 Kbaud)
8.ISO15765-4 CAN(11bit ID,250 Kbaud)
9.ISO15765-4 CAN(29bit ID,250 Kbaud)

LAUNCH CR3001 is with Lifetime Free Update

If the product displays a white screen or cannot support your car, you can solve it by upgrading

Support update system :compatible with Windows XP, Windows 7, Windows 8 & Windows 10

Easy to Carry

The OBD2 scanner's mini size fits comfortably in the palm of your hand. so that you can carry it around no matter in garage or on a trip.

USER-FRIENDLY

Dust Cap Design : protect the connector from dust, water, resistant oil and dirtly , no worries while you donrsquot use it .

LAUNCH CR3001 Update Process :

Step 1 : Go to LAUNCH Website : https://eninfo.x431.com/ , to download Updatetool

Step 2 : Install the updatetool in your company

Step 3 : Connect CR3001 with computer , then Click Update button to Update .

If you still do not know how to do , pls check the update video in the following

How to use CR3001 ?

LAUNCH CR3001 Specifications:

Screen :1.77 " TFT, 160*128dpi
Voltage Range: 9-18V
Operating Temperature :0℃ -50 ℃ (32 ℉ -122 ℉ )
Environment Temperature -20 ℃ -70 ℃ (-4 ℉ -158 ℉ )
Dimension : 118mm*68mm*22.3mm(4.65" *2.68 " *0.88 " )
Weight: <200g