Item specifics
-
Origin
CN(Origin)
-
Item Weight
0.06kg
-
Special Features
Digital Gear Indicator
-
Item Width
4cm
-
Model Name
2398
-
Item Diameter
2cm
-
Item Height
3cm
-
Item Length
5cm
-
Material Type
plastic
Description:
- Condition:100% Brand Ne
- Color of Light Source:Red
- Item Name:Speed Gear Display Indicator
- Size:20mm*30mm*16mm
Foreword:
- This connector is referred as KDS(Kawasaki Diagnostic System) in the Kawasaki manuals.Unlike other gear indicators available for your bike,this product connects to the diagnostic connector.It make the installation very sample. The unit reads data directly from the ECU, offering faster and more reliable readings than competing products.The display is auto learning,there are no button and no "programming wire" Know limitations;Your bike is not equipped with Gear Position Sensor. therefore determining the gear in use is only possible when the engine is running and the clutch is released.
Feature:
- Shows current gear numbe
- Indicates current gear from 1 to max of 6. as well as a neutral indicator
- Auto programmin
- Detects the current gear faster than other gear indicators that use speedometer/tachometer signal
- Display can be mounted anywhere
Installation:
- Find the 4-pole male diagnostic connector(KDS) under the seat,near the ECU box,It has a removable cap and is either semi-transparent or black in color. Note; you may find TWO of this connector on your bike. In this case, try both connectors, but only one of them will supply date to the SEPP gear position indicator.It will not harm your bike if you connect the SEPP gear position indicator to the wrong plug first. Remove the cap,and connect the gear indicator plug.Route the cable to the mounting location. Peel off the green plastic from the back of the unit,and mount the display. Secure the cable with the cable ties supplied,ensuring that the steering movement is not impaired by the cable.
Troubleshooting:
- You may find TWO semi-transparent connectors on the bike with a removable cap or dummy plug.Try the second one if the unit does not work from the first one.Disconnect the SEPP connector and check whether the pins are broken,bent or pushed out of position.Reconnect the plug,and make sure that all connections are good and the connector is fully seated.If you can not execute the setup procedure,your battery might be old or weak.Charge the battery or connect another battery using a jumper cable.If some gears are not indicated properly when the engine is running and clutch is released,rest the unit and setup again.If the problem persists.your clutch might be slipping.
Warranty:
- The unit is completely sealed and epoxy encapsulated, which gives extreme protection for the internal parts from shocks, vibrations and water. To ensure trouble-free operation from the start, all units have been extensively tested prior to shipment.
Package List:
- 1 x Motorcycle Speed Gear Displ
-
Installation Guide:
1.Find the color 4 pole male diagnostic connector, it is usually near the ECU box. Maybe it is one removable cap and partially covered by black tape.
2.After the installation you need set it up.
A.Set your motorcycle rear wheel on the stand frame, turn on the key, the gear indicator is flashing with letter L. It means it is learning now.
B.Start your engine, the letter L will flash to number 1, now you need change gear to 1.
C.In the same way, you set gear 2,3,4,5,6, please remember you need control the tachometer with your right handlebar throttle, the gear position should compatible with your normal RPM.
D.Re-start your engine now, you can see gear number 0,1,2,3,4,5,6
Reset Gear number:
If you set by mistake and some gears did not set in success, you can delete setting.
Turn on the key, when the gear number show 3 or 4 or 5, turn off the key soon.
Repeat this action 6 times, you will see gears 6,5,4,3,2,1,L. Now the deleting process is finish. You can start set gears again.
|
eBike Accessories
Motorcycle Parts