ANCEL PB100 Battery Tester Diagnostic Tool 12V 24V Car Electrical Test Tool AC DC Automotive Power Circuit Probe Tester Kit

ANCEL PB100 automotive circuit tester probe is a must have tool for both professional mechanics and home-use customers who are looking for a fast and accurate solution on 12V - 24V electrical power AVOmeter AC/DC voltage Diode Current Resistance diagnose. Helps you to activate components in the vehicle or W/Ground, read voltage displays red/green polarity LED, tracking, locate short circuits, and bad ground contacts.

Top Reasons to Chose Ancel PB100 Power Probe Circuit Tester

1. Extremely easy to use and highly reliable
2. Built-in Flashlight enables you to work in the dark
3. Easy to read AVOmeter allows you to read voltage, current and resistance at the fingertip
4. With 6 Meter long electronic cable, convenient to test around the car
5. Test mode contain AV Voltage, DC Voltage, Current Resistance, LED, including most car circuit test system
6. Including Cigarette Lighter adaptor, battery test clips, easy to get supply in the car

ANCEL PB100 Electrical System Circuit Tester Functions:

1. Power injection, measuring, ground testing, polarity checking, continuity testing and component activation.
2. Read the AVO meter, voltage, current, and resistance.
3.Energize the electrical components, such as the cooling fan, relay etc.
4. Activate the components
5. Determine the positive, negative and open circuit.
6. Test the bad ground contacts, follow and locate short circuits without wasting the fuse.
7. Test the continuity of the power switch, relay and diode.
8. Protect the tool from overload.
9. Allow you to work in the dark area by using the built-in head light.
10. Test along the vehicle by the long cable.

Continuity Testing
While the diagnostic tool is in resistance mode, using the probe tip with chassis ground or the auxiliary ground lead, continuity can be tested on wires and components attached or disconnected from the vehicle’s electrical system. When the probe tip is contacting a good ground, the LCD will indicate”0.0Ω” and the green LED will be on. A beep tone will sound.

Activating Components in Your Hand
If the green LED went off at that instant or if the circuit breaker tripped, the tool has overloaded. It may be due to the following reasons:
The contact you are probing is direct ground or negative voltage;
The component you are testing is short-circuiting;
The component is at a very high current. If the circuit breaker tripped, reset it by waiting for it to cool down(15 sec).

Testing Trailer Lights and Connections
While the automotive tester in DC Voltage mode, clip the auxiliary ground lead to the trailer ground, probe the contacts at the jack and then apply the voltage to the probe tip, lets you check the function and orientation of the connector and trailer lights. If the circuit breaker tripped, that contact is likely a ground. Reset the circuit breaker by letting it cool down for 15 seconds.

Voltage & Polarity Testing
While the electrical probe tester is in DC voltage mode, contact the probe tip to a POSITIVE circuit. The red LED will light, and the LCD displays the voltage with a resolution of 0.1V. A beep tone will sound. If you contact the probe tip to a NEGATIVE circuit, the green led will light, and the LCD displays the voltage with a resolution of 0.1V. A beep tone will sound. If you contact the probe tip to an OPEN circuit, neither of the LED will light.

Activating Components in the Vehicle
Warning: Haphazardly applying the voltage to specific circuits can cause damage to a vehicle’s electronic components. Therefore, it is strongly advised to use the vehicle manufacturer’s schematic and diagnosing procedure while testing.

NOTE: When powering up components, you can increase the life of power switch if you press the switch first, then contact the tip to the component. The racing will take place at the tip instead of the contacts of the switch.

Signal Circuit Testing
Easy to test the sensor. For example, if you suspect there is a problem with your M.A.P.,

Set the tool in AC Voltage mode, using the probe tip with chassis ground or the auxiliary ground lead;
Connect vacuum pump to MAP sensor;
Contact the probe tip to MAP sensor positive terminal and observe the LCD readings which should be a sine wave in a normal condition;
Apply vacuum, release vacuum and observe the LCD readings. If the LCD readings are abnormal, there is a problem with this sensor.

Ancel PB100 Car Circuit Tester Specifications:

Display: TFT color display (160 x 128 dpi)
Operating Temperature: 0 to 60C (32 to 140F)
External Power: 12.0 or 24.0 V power provided via vehicle battery

Product details

Details information

Ancel PB100 Package List:

1 * PowerScan
1 * Rugged Blow Molded Case
1 * 20ft. Extension Cable
1 * Probe Tip
1 * Battery Hookup Clips
1 * Cigarette Lighter Adapter
1 * User Manual